What's the Best Hot Tub

Author Topic: Caldera heater?  (Read 459 times)

truth649

  • Junior Member
  • *
  • Posts: 5
Caldera heater?
« on: April 13, 2019, 10:53:29 am »
2004 Caldera Tahitian Utopia, heater not working. Thermostat relay clicks on and off as the temperature setting is adjusted. 120VAC from both heater contacts to ground when heater is activated, but no heat. No panel errors or flashing temp light. I have to assume it is a bad heater element but wanted to run it by the experts in case I am missing something stupid. Thanks for any advice!

Hot Tub Forum

Caldera heater?
« on: April 13, 2019, 10:53:29 am »

Tman122

  • Ultimate Member
  • *****
  • Posts: 4046
  • If it Ain't Broke
Re: Caldera heater?
« Reply #1 on: April 15, 2019, 07:57:49 am »
2004 Caldera Tahitian Utopia, heater not working. Thermostat relay clicks on and off as the temperature setting is adjusted. 120VAC from both heater contacts to ground when heater is activated, but no heat. No panel errors or flashing temp light. I have to assume it is a bad heater element but wanted to run it by the experts in case I am missing something stupid. Thanks for any advice!

Checking the contacts to ground is not the proper way to test that heater. What is the resistance from contact to contact?
Retired

bud16415

  • Full Member
  • ***
  • Posts: 654
Re: Caldera heater?
« Reply #2 on: April 15, 2019, 08:39:59 am »
Testing between hot to ground and getting 120v shows you have power. You could also check hot to hot. If your Caldera tub has the double GFCI like mine does the 20a side is the heater and it sounds like you didnít trip that.

Checking the resistance from hot to hot with the power leads removed and the power off should show an open circuit if the heater element is blown.

Sounds like its time for a heater most likely. 

truth649

  • Junior Member
  • *
  • Posts: 5
Re: Caldera heater?
« Reply #3 on: April 15, 2019, 09:59:01 am »
Thanks for the help! I pulled the power leads to the heater and checked the resistance of the element. It is 14 Ohms so the element seems OK. Power across the element before disconnecting it was millivolts when the heater was supposed to be on. It is looking like the relay control board is the culprit.

bud16415

  • Full Member
  • ***
  • Posts: 654
Re: Caldera heater?
« Reply #4 on: April 16, 2019, 07:59:34 am »
You did check to see if the heater side of the GFCI was not tripping?

truth649

  • Junior Member
  • *
  • Posts: 5
Re: Caldera heater?
« Reply #5 on: April 18, 2019, 10:02:28 am »
yes, replaced the relay control board and all is fine now! Easy job, about a half hour start to finish. Thanks everyone!

bud16415

  • Full Member
  • ***
  • Posts: 654
Re: Caldera heater?
« Reply #6 on: April 18, 2019, 03:27:08 pm »
yes, replaced the relay control board and all is fine now! Easy job, about a half hour start to finish. Thanks everyone!

Glad to hear! :)

Spatech_tuo

  • Mentor Level Member
  • ******
  • Posts: 6094
Re: Caldera heater?
« Reply #7 on: April 18, 2019, 05:14:55 pm »
yes, replaced the relay control board and all is fine now! Easy job, about a half hour start to finish. Thanks everyone!

Not a surprise really, always good to hear a 15 year old spa still going strong but some things are unavoidable over time.
220, 221, whatever it takes!

Hot Tub Forum

Re: Caldera heater?
« Reply #7 on: April 18, 2019, 05:14:55 pm »

 

Home    Buying Guide    Featured Products    Forums    Reviews    About    Contact   
Copyright ©1998-2019, Whats The Best, Inc. All rights reserved. Site by Take 42