1
« Last post by Gomboman on November 29, 2024, 12:09:21 pm »
Oh yeah, I haven't gone on here much in the last 10 years. It was a blast in the old days with Terminator, Chas, Spatech_tuo, Dr Spa, yourself and quite a few others. I learned a lot from this forum in the past.
2
« Last post by fishnaked on November 12, 2024, 09:58:53 am »
It was wonderful and fun but, haven't used it in three years. Had it for 10. Kept almost entirely out of the sun. Has always had water in it. Great shape.
The same tub, stove, benches, lid, steps, etc cost $7135 new. Trying to get some idea what to price it at. I was hoping to get around $3000...perhaps a bit more. I just have no idea what people are willing to pay for this style. Great for those who have off-grid places.
What do you all think?
3
Yes, it's normal for the jets or circulation pump on your LS100DX hot tub to run periodically as it heats up to the set temperature.
4
« Last post by ramiroelliot on November 06, 2024, 11:49:20 pm »
My LS100DX was just filled up about 3 hours ago. Starting water temp was about 70f and have it covered and set to heat to 100f. Since I plugged it in, it’s warming slowly which is expected, but the jets keep kicking on. Are the jets (or similar noises) supposed to run while it is getting up to temp? If I go and shut them off, they will restart within 10 mins. They have been running for about 2 hours straight now.
5
« Last post by Chk on November 06, 2024, 09:03:22 am »
I don't think I logged in for more than ten years, lost my tub in the divorce but now have and love my Caldera Tahitian, have had it for 7 years.
Tips for reducing the hardness of my well water? Bought a vanshing pillow but haven't gotten it yet.
Suggestions for geting the rust stains that leaked out of the speakers?
Thanks.
6
« Last post by Mattyrayb on November 01, 2024, 03:46:33 pm »
Last year my control panel fried and I recently bought a replacement panel (Balboa 54640 Circuit Board). Almost everything is exactly the same with the exception of 1 or 2 wires and the switchbank. Should I match it exactly the same as the last one? Wondering if there is a “standard” or “default” that then has the be slightly modified based on the current setup.
7
« Last post by Dr. Spa™ Ret. on September 16, 2024, 06:26:39 pm »
STEVE! I'm older. Retired 10-1/2 years from the industry now.
8
« Last post by icenogle on September 13, 2024, 01:10:08 pm »
Jacuzzi J345 (2015) in the Seattle area. Last year did freeze and a connection on one Motor froze and then leaked I replaced the motor. Still have a slight leak somewhere. Lose about 1" or 2"of water a month during the summer Decided to get rid of it. Just removed the sides And wondered what the chances are it would sell. Otherwise probably going to cut it into pieces And go to the dump and sell se of the hardware, pumps, controller, etc. Anybody been down this road before? .
9
« Last post by eugenewright on September 12, 2024, 03:13:30 am »
Just bought a new spruce wooden hot tub, it need painting on the outside - manual suggests linseed oil which is cheap enough but wondering is there anything better, used Osmo before now and that seems good. Would also like to darken it a bit as its very Pine in colour.
Thoughts please?
10
« Last post by rphman on September 10, 2024, 06:45:11 pm »
I have a 2007 Caldera Moorea that has been good to me thus far. Today I opened it to 4 dashes on the control. I powered it off at the breaker box, it reset and seemed to work. But when I press the jet 2 pump button jet 1 pump starts? If I hit jet 2 pump again it starts in low speed. Seems to be heating when pumps are off and the circ pump is running. I haven't opened it up yet but have a feeling it's the control board? Dam that's expensive was hoping to get a couple more years, any ideas what the problems is? I hate to throw part at it. Been through some circ pumps and heater board so far. Thanks!
|