1
Hot Tub Forum / Re: Checkin in!
« Last post by Dr. Spa™ Ret. on September 16, 2024, 06:26:39 pm »STEVE! I'm older. Retired 10-1/2 years from the industry now.
1
Hot Tub Forum / Re: Checkin in!« Last post by Dr. Spa™ Ret. on September 16, 2024, 06:26:39 pm »STEVE! I'm older. Retired 10-1/2 years from the industry now.
2
Hot Tub Forum / Getting rid of hot tub« Last post by icenogle on September 13, 2024, 01:10:08 pm »Jacuzzi J345 (2015) in the Seattle area.
Last year did freeze and a connection on one Motor froze and then leaked I replaced the motor. Still have a slight leak somewhere. Lose about 1" or 2"of water a month during the summer Decided to get rid of it. Just removed the sides And wondered what the chances are it would sell. Otherwise probably going to cut it into pieces And go to the dump and sell se of the hardware, pumps, controller, etc. Anybody been down this road before? . 3
Hot Tub Forum / what to treat a Wooden hot tub« Last post by eugenewright on September 12, 2024, 03:13:30 am »Just bought a new spruce wooden hot tub, it need painting on the outside - manual suggests linseed oil which is cheap enough but wondering is there anything better, used Osmo before now and that seems good. Would also like to darken it a bit as its very Pine in colour.
Thoughts please? 4
Hot Spring Spas / 2007 Caldera Moorea 4 dashes on control« Last post by rphman on September 10, 2024, 06:45:11 pm »I have a 2007 Caldera Moorea that has been good to me thus far. Today I opened it to 4 dashes on the control. I powered it off at the breaker box, it reset and seemed to work. But when I press the jet 2 pump button jet 1 pump starts? If I hit jet 2 pump again it starts in low speed. Seems to be heating when pumps are off and the circ pump is running. I haven't opened it up yet but have a feeling it's the control board? Dam that's expensive was hoping to get a couple more years, any ideas what the problems is? I hate to throw part at it. Been through some circ pumps and heater board so far. Thanks!
5
Hot Tub Forum / Caldera Vacanza Problems« Last post by mitchfloyd on September 08, 2024, 10:35:52 am »Hello, Has anyone had a problem with their Caldera Vacanza 2015 not heating up. I have checked the parameters and the cleaning timer is working fine, the filter is not clogged or dirty. I have tried turning it off and on again but to no avail, there is no error code and the Start light is flashing.
Has anyone had a similar problem? Thanks. 6
Hot Tub Forum / Re: Looking for info« Last post by cranbiz on September 03, 2024, 04:39:08 pm »Vita Spa's are owned by Maxx Spas. They share a lot of the same technology. They are not one of my top choices but they don't suck either.
My top choices are Hot Springs/Caldera, Sundance and Artesian. Most Maxx Spas use perimeter insulation. I'm not in the camp where this is better than full foam. They are usually easier to work on but they are not as well insulated as a full foam tub. More important is the dealer support. If your dealer sucks, your service will suck. Warranty is covered by the dealer. It's very necessary to ask the dealer questions about warranty and if possible, speak to others who have bought from the dealer. 7
Hot Tub Forum / Looking for info« Last post by drprwnap on August 17, 2024, 05:13:04 pm »Just visited a dealer that carries Hot Springs spas. Was shown an Envie spa from Vita spas. Never heard of this company before. Any feedback would be much appreciated.
8
Hot Tub Forum / Re: Checkin in!« Last post by Flyonthewall on July 31, 2024, 08:10:24 pm »are you still in the hot tub industry steve? i liked reading the exploits of you originals back in the day, like term from texas. the super custom fallsburg spa was always good to elicit some fun give and take.
9
Hot Tub Forum / Re: Cedar hot tub« Last post by cranbiz on July 25, 2024, 05:16:12 pm »Your meter does Chlorine, Alkalinity and PH.
Bromine is read under the CL reading which is why it says to take the free chlorine reading and multiply by 2.2. Bromine does need to be in a higher concentration. 10
Hot Tub Forum / Cedar hot tub« Last post by Revid on July 23, 2024, 09:07:21 am »I have a cedar hot tub and bought a Aquachek meter to read levels. Iam using bromine cause I read it was better for the cedar wood. The meter has CL, PH and ALK on the screen for readings. What are my bromine levels supposed to be and under what space should it be CL or ALK? The paper said it supposed to read bromine and booklet says to multiply free chlorine by 2.2
|