Hot Tub Forum
Original => Hot Tub Forum => Topic started by: matt84 on October 07, 2017, 11:45:10 am
-
Hello everyone! ,
I'm new to this forum , hopefully someone can help me out with this problem!
i recently had to install a new board for my tub, its the balboa VS501z board with a 2 speed pump. the old one burned up with a loose connection on a power wire. i ordered the same board as a replacement hoping that it would be a simple plug and play , unfortunately I plug in the motor and it cycles on and off every 2 seconds causing the start capacitor to burn out. After replacing it i tried again and same outcome.
I've tested the voltage coming in and its fine,
motor is in good working order, I bench tested it and both high and low speeds work when given 120 volts,
I checked the output on the board for the motor and it reads 120 volts then when switched to high speed the other line goes to 120, (working correctly . Once the motor is plugged in is when the problem starts.
i can include photos if that helps anyone!
thanks for taking the time to look at this
Matt.
-
Try unplugging the control panel and see if the motor will run normally during the filter / heat cycle, which are programmed into the circuit board. Could be a stuck jet button on the control panel.
-
i just tried running it without the controls hooked up same result as before motor cycles on and off
-
i just tried running it without the controls hooked up same result as before motor cycles on and off
Is there 220V going to the pump or 110v? You may have a dip switch problem.
-
120 volt to pump, when it switches from high to low it is switching power to the high side, shutting off the low speed power. i have noticed it seems to not be pushing as much water as well.
-
120 volt to pump, when it switches from high to low it is switching power to the high side, shutting off the low speed power. i have noticed it seems to not be pushing as much water as well.
OK next question is it a 220V pump? I think it likely is. The new board has dip switches so it can handle both 120V pumps and 220V pumps. Did the board come with a manual or instruction sheet?
-
the motor for some reason does not have a nameplate on it,
I took the motor off and bench tested it, sending 120 volts to the red/white wire, then to the black/white. Doing this changed the speed on the motor from lo to hi, i haven't put 240 to the motor as i assumed doing that first test ruled out it being a 240 volt motor. i think it has two 120 volt windings. As far as the dip switches go, nothing was flipped on. I compared it to the old one and it has the same layout for the dip switches.
thanks for taking the time to help me! very appreciated.
-
with the motor turning on and off , could this be a sign of the motor going bad? I'm not sure if I'm missing something obvious...
-
with the motor turning on and off , could this be a sign of the motor going bad? I'm not sure if I'm missing something obvious...
Is the power going to the motor also intermittent? Or is it steady when its energized?
-
The power going to the motor seems to be steady, when it starts turning on and off I can hear the relay switching as well, I let it run for a while and got an error which indicated a temp difference , (caused by low flow) the motor doesn’t seem to be able to go into high speed mode when connected to the panel .
-
The power going to the motor seems to be steady, when it starts turning on and off I can hear the relay switching as well, I let it run for a while and got an error which indicated a temp difference , (caused by low flow) the motor doesn’t seem to be able to go into high speed mode when connected to the panel .
I was a parts replacer. Trouble shooting is hard. I had several pumps in my inventory that I could slap in to see if a pump was bad. I also had some boards in case that was the problem. In your case yea, it may be the pump, but you don't have the option of trying a different pump to see if it fixes the problem. Or changing out the board to see if you have another faulty board.
-
i have a friend giving a working motor to test and see if thats the issue, ill post the results once i get it!
hopefully this fixes it.
-
all fixed! the motor was fine... it didn't have a label so i had assumed it was 120 when i talked to the motor repair guy, i was wrong, simple change of wiring in the control panel and it runs great! thanks again everyone , very rookie mistake!! :o
-
all fixed! the motor was fine... it didn't have a label so i had assumed it was 120 when i talked to the motor repair guy, i was wrong, simple change of wiring in the control panel and it runs great! thanks again everyone , very rookie mistake!! :o
I was on the right track from the beginning. But it's hard to fix things through a forum.