Original > Hot Tub Forum

Placing Hot Tub on Pavers Help!!

(1/2) > >>

gina_nicole:
Feel like I've read every thread possible but looking for a simple answer I can't seem to find anywhere!! I currently have this paver patio laid in my backyard and I wanted to know if I can place the hot tub on top of the pavers that are already laid. As you can see, the pavers are slightly uneven (its very slight, less than an inch with some in the middle being a little higher than where the outsides would like) and I know hot tubs are supposed to be level.

Here are photos: https://ibb.co/5FD5W3c
https://ibb.co/981vTN5


My question is what is the best way to level the hot tub on this surface?

Is there a need to buy Handi-Spa pads and will placing a Spa Pad over this area make the hot tub sink in more level? https://www.spadepot.com/Handi-Spa-Pads-Box-of-3-P847?zmam=55673001&zmas=1&zmac=1&zmap=AC1058&gclid=EAIaIQobChMIx-e07aSV5wIVnv_jBx0o5AiREAQYBSABEgJllvD_BwE are what I am referring to
 
Can I just buy heavy duty wedges and slide them around the hot tub to make up for the extra space? https://www.amazon.com/Ez-Shim-Heavy-Duty-Shims-count/dp/B002Y0LIQE
 

Is another option to lay a level of gravel down to try to make up for some of the unevenness on top of the rocks?
Or can someone just tell me if this uneven paver really isnt that terrible and I really shouldn't worry about it in the long run? Help is GREATLY APPRECIATED!! :) hot tub is here next week so I do not wan to dig up the pavers. I can always get a pad and put it on the grass but I've read pavers are a good choice.

Thank you!!

bud16415:
You want the pad both level and flat. Those are two different things. Level means the water wont be high on one side and low on the other. I would say level within a half inch is a reasonable goal and you may want it slightly out of level to allow water (rain) to drain away from the house. Flat is the other condition. A hot tub full of water will weigh maybe 6000 pounds. You don’t want to stress the tub and frame having it just sitting on a high spot. Of course there is limits to how flat is flat but if you have an inch I would say that is way to much. I wouldn’t use wedges as the tub needs support in the center as well as the sides and I wouldn’t want wedges sticking out.

It is easy with a 4’ level and a nice straight 2x4 to check the area you want the tub. It is also easy to pull up a high paver and remove a little sand and reset the paver. It is just as easy to pull a low one and add some sand.

I would take the time maybe a few hours and make it right before they show up. You also have to plan the location for your GFCI and how you will be running power to the tub.

Welcome to the forum and to your new tub. I was in mine this morning it was about 20f out and a wonderful time. You look like a warmer place but think about your location and the views and what direction the cover will open etc. 

gina_nicole:
thanks for the reply here - those pavers are actually cemented very nicely/tightly together - i am not sure I am going to be able to remove them on my own and unfortunately, don't have anyone handy that can do it nearby. it sounds like I'd be safer with adding a spa pad into the grass and putting it on top of there? it's so hard for me to tell because some of them are just slightly raised, when I eyeball it, seems like it would be evened out pretty well, but spending over 5k on the tub, would like it to last. theres a few in the middle that are slightly raised and it evens out on the outsides, its under an inch all around.

is there any sense in laying gravel over the top of the pavers or any other suggestions? the outlet is going right where those pavers are, so thats why im trying to have it placed there, there is a power box near by - totally looking forward to the lake views and the tub! thanks for the help!

bud16415:
From what little I can tell from your photos the paver pad looks flat enough. It does look like the pad slopes from the house down to the lawn area. That tilt wont effect your tub working but will make the water a little deeper on one side.

What kind of tub is it and what voltage? If it is a smaller 120V tub that will likely not be so noticeable if it just plugs in I would try it on the pad and see how it goes. You can always drain it and move it at any time if it is a plug n play tub. It would take a couple big guys to slide it.

Tman122:
I agree they look flat enough. But use a straight 2x4x8 to check that slope. A 1/2" is OK. But an inch can be an eyesore for the water in the tub.

Navigation

[0] Message Index

[#] Next page