Brand Specific Forums > Bullfrog Spas
Bullfrog R6L 1 pump
Compatico:
--- Quote from: Tman122 on March 05, 2016, 08:05:53 am ---
--- Quote from: Compatico on March 04, 2016, 08:20:56 pm ---Not quite...a circ pump is typically about 1 amp (230w) and a jet pump is about 4 amps (920w) on low which is used for filter cycles. Do the math and the circ pump will draw about 150% more power over a 24 hour period vs 4 hour filter cycle (5520 vs 3680). In my area we're blessed (sarcasm) with a hydro company that bills us too much during the day but less at night. I intend to set up filter cycles to run during "off peak" hours and save even more over the 24/7 circ pump.
--- End quote ---
But you forgot to calculate jet pump run time between filter cycles to maintain heat. Which you won't have on a circ pump tub.
--- End quote ---
Oh so the circ pump goes through the heater element? Are you sure about that because the flow rate would be very low causing the water to heat about 4x higher in the same chamber and contact time compared to a jet pump pushing the water through the heater?
(EDIT) just googled and it seems the circ pump does push water through the heater.
I'm sure the cycling of a jet pump to heat would still be in that 50% extra range though, so you might still break even for usage. If not I'm guessing it would be close enough to not be a major factor.
Spatech_tuo:
--- Quote from: Compatico on March 05, 2016, 10:23:06 am ---
--- Quote from: Tman122 on March 05, 2016, 08:05:53 am ---
--- Quote from: Compatico on March 04, 2016, 08:20:56 pm ---Not quite...a circ pump is typically about 1 amp (230w) and a jet pump is about 4 amps (920w) on low which is used for filter cycles. Do the math and the circ pump will draw about 150% more power over a 24 hour period vs 4 hour filter cycle (5520 vs 3680). In my area we're blessed (sarcasm) with a hydro company that bills us too much during the day but less at night. I intend to set up filter cycles to run during "off peak" hours and save even more over the 24/7 circ pump.
--- End quote ---
But you forgot to calculate jet pump run time between filter cycles to maintain heat. Which you won't have on a circ pump tub.
--- End quote ---
Oh so the circ pump goes through the heater element? Are you sure about that because the flow rate would be very low causing the water to heat about 4x higher in the same chamber and contact time compared to a jet pump pushing the water through the heater?
(EDIT) just googled and it seems the circ pump does push water through the heater.
I'm sure the cycling of a jet pump to heat would still be in that 50% extra range though, so you might still break even for usage. If not I'm guessing it would be close enough to not be a major factor.
--- End quote ---
The circ pump is really valuable if sound is an issue for whatever reason (on a deck, next to a bedroom, close to the neighbor...) since it so much quieter and if you have ozone it allows it to run 24/7.
Its also less expensive to run that the 2 speed pump as TMan noted earlier but I agree with you that part shouldn't be enough of a cost savings to be a major difference.
Tman122:
--- Quote from: Compatico on March 05, 2016, 10:23:06 am --- If not I'm guessing it would be close enough to not be a major factor.
--- End quote ---
I think this was mentioned a couple posts in.
red2play:
I love my BullFrog. I have the R6L and as others have stated, you don't use diverter valves, you can simply turn off anything you don't use. My wife likes the rainfall one but I like the neck massager and the Cascadia we both like. Its perfect for me because its completely customizable and its not like your going to keep adjusting. You adjust once (unless your picky) and it should work just fine without any more adjustments. Its NOT like an android. There aren't any quirks or anything difficult, you simply twist the knob on your choice of massage to your desired pressure. I do turn off the rainfall one when I want a hard neck massage.
I know when I wet tested the other spas, they didn't seem as powerful. Even when they had two pumps. The diverter knob only shut off one side but when I wanted to, I could shut off ALL of the other pumps to make it blast out (that's not the case anymore).
However, a couple of points:
1. Don't let anyone sit on the filter cover, mine broke because my daughter would keep sitting on it.
2. I find myself only using the customized jets, I don't use the built in ones (maybe that's why I think its more powerful). I rarely have guests in my spa as I don't trust many to be 'clean' or follow directions and since I'm normally the only one or its just me and my wife, we don't need the built in ones. When you wet test, be SURE to turn off all built in jets as you won't need them 90% of the time unless you party every week.
3. Be sure to ask the salesperson how much work that you think your going to put in for cleaning and water balance (this is for any spa) so they can recommend a system for clean water that will match your willingness to work on the spa.
Oh yeah:
http://www.whatsthebest-hottub.com/forum/index.php/topic,17507.0.html
Hottubguy:
--- Quote from: red2play on March 06, 2016, 09:28:14 pm ---I love my BullFrog. I have the R6L and as others have stated, you don't use diverter valves, you can simply turn off anything you don't use. My wife likes the rainfall one but I like the neck massager and the Cascadia we both like. Its perfect for me because its completely customizable and its not like your going to keep adjusting. You adjust once (unless your picky) and it should work just fine without any more adjustments. Its NOT like an android. There aren't any quirks or anything difficult, you simply twist the knob on your choice of massage to your desired pressure. I do turn off the rainfall one when I want a hard neck massage.
I know when I wet tested the other spas, they didn't seem as powerful. Even when they had two pumps. The diverter knob only shut off one side but when I wanted to, I could shut off ALL of the other pumps to make it blast out (that's not the case anymore).
However, a couple of points:
1. Don't let anyone sit on the filter cover, mine broke because my daughter would keep sitting on it.
2. I find myself only using the customized jets, I don't use the built in ones (maybe that's why I think its more powerful). I rarely have guests in my spa as I don't trust many to be 'clean' or follow directions and since I'm normally the only one or its just me and my wife, we don't need the built in ones. When you wet test, be SURE to turn off all built in jets as you won't need them 90% of the time unless you party every week.
3. Be sure to ask the salesperson how much work that you think your going to put in for cleaning and water balance (this is for any spa) so they can recommend a system for clean water that will match your willingness to work on the spa.
Oh yeah:
http://www.whatsthebest-hottub.com/forum/index.php/topic,17507.0.html
--- End quote ---
Do you ever turn the jets on you don't use? I would just to purge all the lines so nasty stuff doesn't start building up in there
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version